Line
$11k/ still / mo
Cut-state control on a single still with safety enforcement and audit.
Talk to us
The cut, made on spec, every single run.
The cut is the most valuable and most safety-critical call in the stillhouse, and it is still made largely by hand and nose. Cutrix estimates the heads, hearts, and tails boundary live and holds the hearts on character inside hard methanol limits.
- Off-spec spirit
- down
- Hearts yield
- up
- Methanol limits
- enforced
Fermion
→
Cutrix
→
Nosera
→
Caskora
→
Bottlex
What it does
Finds the boundary in real time
A few minutes or a degree too early or late gives you harsh, low-yield, or unsafe spirit, and the right cut point drifts with the wash, the still, and the weather. Cutrix reads the run continuously and estimates where the heads end and the tails begin, run after run.
- Estimates the heads, hearts, and tails boundary from telemetry and inline spectra.
- Holds the hearts on character while staying inside hard methanol and safety limits.
- Maximizes yield without pushing feints into the spirit.
CUT STATELIVE
How it works
Control with the brakes built in
Cutrix ingests Fermion's characterized wash and Nosera's inline readings alongside still telemetry, then controls reflux, heat, and cut timing. Safety limits are hard constraints, not suggestions. The distillery twin can rehearse a cut before the still fires.
- Cut-state estimation from multivariate telemetry and spectra.
- Reflux, heat, and timing control tuned for yield inside safety bounds.
- Per-distiller craft memory that captures the calls your team approves.
Autonomy, on your terms
- Shadow mode reads the run and shows the boundary it sees.
- Assist mode recommends the cut for the operator to confirm.
- Bounded autonomy acts inside hard methanol and quality limits.
Capabilities
The craft of the cut, encoded and auditable
Cut-state estimator
Reads the evolving heads, hearts, and tails boundary from live telemetry and spectra.
Safety guardrails
Predicts and enforces methanol and safety limits as hard constraints on every run.
Yield optimization
Pushes for hearts recovery without letting feints reach the spirit.
Craft memory
Captures the cut decisions each distiller approves so the house style carries forward.
Release-grade audit
Writes an immutable trail for quality release and excise and safety review.
99%+uptime target
1 cutheld on spec
100%runs logged
Signals
What Cutrix reads on the still
Every recommendation traces back to signals your team can open and check.
| Signal | Source | What Cutrix does |
|---|---|---|
| Plate / column temps | Still telemetry | Tracks the cut state as vapor composition shifts. |
| ABV / reflux | Inline meters | Controls reflux and heat to hold the hearts on character. |
| Inline spectra | Nosera sensing | Reads congener and methanol signals in real time. |
| Wash profile | Fermion passport | Anticipates the cut from how the wash was built. |
| Copper contact | Still config | Adjusts for how the still shapes the spirit that day. |
Inside the stack
The anchor of the stack
Cutrix sits at the center of Caskent. It consumes Fermion's wash and Nosera's live sensing, makes the call that most determines quality and yield, then hands the fill chemistry to Caskora so maturation starts from a known point. The more stills run on it, the better its read of every cut across the fleet.
Pricing
Start on one still, expand plant-wide
Land where the pain is, prove the lift, then grow vessel by vessel and site by site.
Distillery
$70k/ mo
Whole stillhouse, plus the full Caskent autonomy stack.
Talk to usEnterprise
$500k-$6M ACV
Multi-site still fleets with custom control policies and SLAs.
Talk to usQuestions
Common questions
How does it keep spirit safe?
Methanol and safety limits are hard constraints. Cutrix will hold the cut inside them even when that means leaving some yield on the table, and it logs every decision.
Does it replace our master distiller?
No. It captures and scales the calls your distillers approve. They set the house style and the limits, and Cutrix holds to them run after run.
Pot still or column?
Both. Cutrix works across pot and column stills for whisky, vodka, gin, rum, tequila, and brandy.
Hold the hearts on spec, every run.
See Cutrix read a live cut and hold it inside your limits.